公司新闻

您的位置:网站首页 > 公司新闻

工业油雾净化器

 

油雾收集净化器工作原理:
      油雾从吸气口进入过滤室,被吸附在气液烧结网上,经聚集、结合等效应后,在重力的作用下滑落、下沉到底部,通过排油管,排到油槽被收集。剩下的小部分油雾在过滤室出口处完全被特种初效过滤毡吸收,同样的被收集到油槽。出风口排出的有异味的空气,被消音器内的活性炭吸附,消除干净。洁净的空气排放到车间可再次循环利用。
      本产品设计为三级过滤,第一级过滤采用气液烧结网覆PTFE膜(聚四氟乙烯),表面光滑,吸油性强,可反复清洗使用;第二级过滤是特种初效过滤毡,第三级为高效活性炭层,清除异味。整机外形美观,安装使用方便,除油烟效果比较明显。
 
      现代机械加工领域,一般使用乳化液或冷却油作为作为冷却液,从而产生大量的油雾油烟,0.3-3.5微米的颗粒会吸入人体内对健康构成危害、油雾沉积在工作区,易造成工伤等事故,有害于员工的身心健康;同时工作场所雾气弥漫,降低生产效率;油雾沉积在墙面,设备上有着潜在火灾隐患,并可能成为机床内部和电气系统故障的原因。如果将雾状物排向室外,会破坏环境。
 
应用范围:
      可用于切削油、柴油及合成冷却液作为冷却液在加工时产生的油雾及水性雾气。
应用范例:
      CNC数控车床、清洗机、外圆、平面磨床、滚齿、铣床和插齿机床、真空泵、喷雾试验室、电火花加工、数控加工中心。
选型说明:
   全封闭机床:风量Q(m3/min)=(W×D×H)α 
        W×D×H:加工腔体体积(m3) 
α:加工腔体每分钟的换气量(回/min)(经验定数)
◇加工时间一个小时以上的,α=5
◇加工2-3分钟,取8
◇加工2分钟以内,取10

Working principle of the oil mist purifier collection:
Oil mist from the suction mouth into the filter chamber, and adsorb on the gas and liquid sintering online, after assembled and combined effect of the gravity slide, sinking to the bottom, through the line of tubing, into the oil tank is collected. The rest of the small oil mist in the filter chamber exit completely absorbed by the early special effect filter felt, to be collected the same tank. Smell of the air outlet discharge, was activated carbon adsorption in the muffler, remove and clean. Clean air emissions to the workshop can be recycled again.
This product design for triple filter, the first level filter adopts gas and liquid sintering net PTFE (PTFE) membrane, smooth surface, oil absorption is strong, can use repeatedly washing; Second-level filtering is special effect filter felt, at the beginning of the third level is efficient activated carbon layer, remove peculiar smell. The machine good appearance, easy installation and use, in addition to lampblack effect is obvious.
Modern machining area, the use of cooling oil emulsion or as a general as a cooling fluid, resulting in a large amount of oil mist lampblack, 0.3 to 3.5 micron particles will inhale to pose health risks in the human body, oil spray deposition in the workspace, easy cause inductrial injury accident, harmful to the physical and mental health of employees; Foggy workplace at the same time, reduce the production efficiency; Oil mist deposition on metope, equipment has a potential fire hazard, and might be inside the machine and electrical system failure reasons. If mounted to the outside, the mist will damage the environment.
Scope of application:
Can be used for cutting oil, diesel oil and synthetic cooling fluid as the coolant in the processing of oil mist and water mist.
Application examples:
CNC numerical control lathe, washing machine, cylindrical, surface grinding machine, gear hobbing and milling machine and the slotting machine, vacuum pump, spray test chamber, electrical discharge machining, CNC machining center.
Selection of details:
Fully enclosed machine: air Q (m3 / min) = alpha (W * D * H)
W * D * H: processing cavity volume (m3)
Alpha: processing cavity per minute ventilation (back/min) (destiny)
Cardiac processing time more than an hour, alpha = 5
Cardiac processing for 2-3 minutes, take 8
Cardiac processing within 2 minutes, take 10